GATES G-FORCE C12 30C3750 – CVT Drive Belt for Can Am, Ski Doo, Massimo, Odes, Online, Stels

96,90  96,90 

GATES G-Force C12 CVT Belt 30C3750 – Can Am, Ski Doo, Massimo, Odes, Online, Stels

Replaces OEM # 21050831000, 420280360, 420280362, 42280360, 7150000302, 715900030, 715900212

  • optimal heat resistance
  • Advanced carbon tensile cords offer increased durability
  • Aramid fibre-loaded undercord guarantees optimum belt life
  • Neoprene component guarantees top performance
  • precise fit to the Original Equipment (OE) belt
  • no need for clutching adjustments at installation
  • Made in USA

Please note the vehicle model list!

Delivery time: 2 - 5 Tage

In stock (can be backordered)

GATES G-FORCE C12 CVT Belt 30C3750 for Can Am, Ski Doo, Massimo, Odes, Online, Stels

The innovative G-Force C12 belts with carbon tensile cord design combine minimal stretch with extraordinary strength. The belt design allows for maintaining peak power throughout the shift curve. In addition, the carbon tensile cord provides optimal power transmission, resulting in faster acceleration, improved throttle response and consistent shifting performance.

Gates G-Force C12 belt, the first CVT belt with carbon tensile cords.
G-Force C12 CVT belts for even better performance and for faster acceleration, improved throttle response and consistent shifting performance! Advanced carbon tensile cords offer increased durability. Trapezoidal top cog and rounded bottom cog design offers superior flexibility and heat dissipation. Reinforced fibre-loaded compound guarantees optimum durability

WHY G-FORCE C12?

  • Neoprene component guarantees top performance.
  • Advanced carbon tensile cords offer increased durability.
  • Minimal stretch with extraordinary strength.
  • Designed to meet or exceed OE standards.
  • First CVT Belt with carbon tensile cord design.

Made in USA

ATTENTION
Not only correct assembly but also correct retraction of the belt is extremely important for the service life of every belt!

Please note the vehicle model list!

Installation

CVT-BELT INSTALLATION & BREAK IT IN

Not only correct assembly but also correct retraction of the belt is extremely important for the service life of every belt!

NEW BELT INSTALLATION

Choosing the right belt for your vehicle is critical for optimum performance. Please use the JAY PARTS drive belt finder. To ensure optimal operation of newly installed belts, the CVT sheaves must be cleaned of all old belt residue, dirt, debris, and oils. If any particles remain, belt slip and a noticeable drop in vehicle performance can occur

Jay Parts Reinigung Veriomatik vor Riemenwechsel

At JAY PARTS  there is a 3D-Softflex – Non-Woven Abrasives-Pad FREE of charge with every GATES G-FORCE REDLINE CVT drive belt! Remove old belt residue, dirt, debris, and oils from the clutch sheaves with 3D-Softflex non-woven abrasives pad and isopropanol alcohol or acetone poured or sprayed on a rag.
ATTENTION: Do not spray onto the clutches and do not use brake cleaner.

  1. Make sure the vehicle is in park or neutral and the engine is off. Remove the cover of the clutch.
  2. If possible, blow out the clutches and all inlet and outlet openings in the clutch box with compressed air to remove dust, dirt and debris. If the previous belt broke, remove all the debris and cord if any are left in the primary or secondary clutches. Completely clear all inlets and outlets, especially the variomatic outlet, of any belt residue.
  3. If possible, check for correct alignment by checking the center-to-center distance between the primary and secondary clutch, see the vehicle manufacturer’s manual.
  4. Clean the clutch sheaves with the 3D-Softflex Non-Woven Abrasives-Pad and wipe them clean with isopropanol alcohol or acetone poured or sprayed on a rag – do not spray onto the clutches. Repeat this procedure until the sheaves surfaces are completely cleaned and dry. Do NOT use brake cleaner!
    This removes the old belt residue and oils which can cause the new belt to slip.
  5. Open the secondary clutch with suitable tools as recommended by the OEM. Install the new belt so the lettering can be read right side up. Although G-Force belts are not directionally biased, it is recommended to install them with the label lettering facing toward the user to keep belt reinstallation consistent. DO NOT FIT THE NEW BELT WITH A LEVER. (Note: When reinstalling the belt, always install it in the previous orientation to keep the belt wear profile aligned with the sheaves profile.)
  6. After installation, release the tension on the secondary clutch. Turn the secondary clutch anticlockwise until the belt reaches its initial position.
  7. Remove the tool that may have been placed on the vehicle.
  8. Mount the clutch cover on vehicles with a vario shaft mounted in the cover. If the vario shaft isn’t mounted in the cover, start unit up in park and let it idle for 30 seconds. Turn off the engine and replace the clutch cover. Give a quick throttle.
    CAUTION: DO NOT reach into the clutch (rotating parts)
    If the belt doesn’t come to rest and stop spinning in Park and the idle has dropped to normal warm engine rpm, check your system for alignment and proper operation of the variomatic. On snowmobiles you may need to adjust your deflection several times.
  9. See the vehicle Owner’s Manual for proper alignment and center-to-center distances of the clutch system.
  10. When the belt stops in park and neutral mode, replace the cover and proceed to break-in process of a new belt.

PERFORM A HEAT CYLE – DON’T BREAK IT. BREAK IT IN.

If you take the time to break in a new belt gently and carefully, the belt will run smoother and you will have maximum life and performance. Follow the next HEAT CYCLES:

  1. Drive the unit in two wheel high for 20 minutes between 25-45 mph (40-72 km/h) avoiding hard accelerations and hills. Flat terrain works best. Vary vehicle speed and engine rpm to cycle the belt in the normal operating range, but not more than ¾ of the maximum force during retraction. In extremely cold weather, it is advisable to extend the break-in time by 5-10 minutes to allow the belt to warm up optimally.
  2.  After 20 minutes of driving, let the unit cool down for 30 minutes with the motor off.
  3. Repeat the HEAT CYCLE for a second time. Let the belt cool down again for 30 minutes.
  4. Repeat the HEAT CYCLE for a third time. Let the belt cool down again for 30 minutes and you have a well broken in belt.
KAT/CAT Marke/Brand Jahr/Year Modell/Model
KAT/CAT Marke/Brand Jahr/Year Modell/Model
Belt Can Am 2006 - 2015 Outlander 800
Belt Can Am 2007 - 2015 Outlander 500
Belt Can Am 2007 - 2015 Outlander MAX 500
Belt Can Am 2007 - 2015 Outlander MAX 800
Belt Can Am 2007 - 2015 Renegade 800
Belt Can Am 2007 - 2018 Outlander MAX 650
Belt Can Am 2007 - 2020 Outlander 650
Belt Can Am 2008 - 2015 Renegade 500
Belt Can Am 2011 - 2020 Commander 1000
Belt Can Am 2011 - 2020 Commander 800
Belt Can Am 2012 - 2020 Outlander 1000
Belt Can Am 2012 - 2020 Renegade 1000
Belt Can Am 2013 - 2017 Maverick Max 1000
Belt Can Am 2013 - 2018 Maverick 1000
Belt Can Am 2013 - 2018 Outlander MAX 1000
Belt Can Am 2014 - 2019 Commander MAX 1000
Belt Can Am 2015 - 2018 Outlander XT 1000
Belt Can Am 2015 - 2018 Outlander XT 650
Belt Can Am 2015 - 2019 Commander XT 1000
Belt Can Am 2015 - 2019 Commander XT 800
Belt Can Am 2015 Outlander XT 500
Belt Can Am 2015 Outlander XT 800
Belt Can Am 2016 - 2018 Outlander MAX 570
Belt Can Am 2016 - 2018 Outlander MAX 850
Belt Can Am 2016 - 2018 Outlander XT 570
Belt Can Am 2016 - 2018 Outlander XT 850
Belt Can Am 2016 - 2020 Outlander 570
Belt Can Am 2016 - 2020 Outlander 850
Belt Can Am 2016 - 2020 Renegade 570
Belt Can Am 2016 - 2020 Renegade 850
Belt Can Am 2017 - 2019 Commander MAX 800
Belt Massimo 2018 - 2019 MSU850
Belt Massimo 2018 - 2019 Warrior800
Belt Odes 2014 - 2015 Dominator 1000
Belt Odes 2014 - 2015 Dominator 800
Belt Odes 2014 - 2017 Raider 1000
Belt Odes 2014 - 2017 Raider 800
Belt Odes 2014 - 2019 Assailant 800
Belt Odes 2017 - 2019 Dominator 1000
Belt Odes 2017 - 2019 Dominator 800
Belt Odes 2018 - 2019 Ravager 1000
Belt Online 2014 - 2021 X9.0
Belt Online 2017 - 2021 X9.1
Belt Stels 2010 - 2021 Guepard 650
Belt Stels 2010 - 2021 Guepard 800
Belt Stels 2010 - 2021 Guepard 850

Reviews

There are no reviews yet.

Add a review

Produktanfrage / Request to product: GATES G-FORCE C12 30C3750 - CVT Drive Belt for Can Am, Ski Doo, Massimo, Odes, Online, Stels

    Datenschutz-Info akzeptiert * Datenschutz-Info gelesen und akzeptiert / I have read and accept the Data protection.

    You may also like…