Bearing clamp steering + reinforcement for steering stem

153,04  153,04 

JAY PARTS bearing clamp steering JP0066 + reinforcement for steering stem Polaris Scrambler / Sportsman
for the original steering stem or Jay Parts steering stem performance

  • aluminum bearing clamp
  • highly abrasion-resistant and self-lubricating plastic bushing
  • greasing possible
  • seald against whater & dust
  • steel reinforcement 4-fold screw connection possible
  • minimized wear
  • increased stability and safety

To optimize and strengthen the bulkhead (aluminum steering head), we have combined the bushing with the steel reinforcement (4-bolt fitting possible). Thus, it distributes the pressure under excessive load (fall) on the 5-fold surface and minimizes expensive consequential damage.

Availability : in stock

In stock (can be backordered)

JAY PARTS bearing clamp steering JP0066 + reinforcement for steering stem Polaris Scrambler / Sportsman
for the original steering stem or Jay Parts steering stem performance

 

Our combination of a heavy duty bearing clamp with special bushing made of a highly abrasion-resistant and self-lubricating plastic with a helical groove is simply ingenious. The grease can be optimally distributed over the entire bearing surface via a grease nipple. The ingress of water and dust will be prevented by 2 O-rings.

To optimize and strengthen the bulkhead (aluminum steering head), we have combined the bushing with the steel reinforcement (4-bolt fitting possible). Thus, it distributes the pressure under excessive load (fall) on the 5-fold surface and minimizes expensive consequential damage.

In the combination we recommend the Jay Parts STEERING STEM PERFORMANCE with part number JP0064

IMPORTANT
If the bearing surface of the steering column is already worn (metal abrasion is present), our system does not improve either. Here we also recommend a new steering stem.

FEATURES
- aluminum bearing clamp
- highly abrasion-resistant and self-lubricating plastic bushing
- greasing possible
- steel reinforcement 4-fold screw connection possible
- minimized wear
- increased stability and safety
- best possible material and ideas composition

Replaces original part numbers: 5262582 + 5438904

DELIVERY
- bearing clamp
- bushing
- reinforcement plate
- screws & nuts
- grease nipple
- 2 O-rings

WORKS WITH THE FOLLOWING MODELS
Polaris Scrambler 850 / 1000 2013-
Polaris Sportsman 550 / 850 / 1000 2009-

ATTENTION
When greasing, only apply grease until the first resistance is detected at the grease gun. Grease must not ooze out! If grease swells out, the O-ring is damaged and the seal against water/dirt is no longer given!

Assembly instructions

Jay Parts Lagerbock JP0066 + Verstärkung für die Lenksäule

BEARING CLAMP STEERING + REINFORCEMENT FOR STEERING STEM

We recommend professional installation at one of our Flagshipstore Partners!

Drill a 5mm hole from the front into the bulkhead to instasll the grease nipple. The supplied grease nipple has a self-tapping thread (no tapping necessary).
When drilling, make sure that no cables are damaged. Place something under the drilling point to catch the drilling chips.

When mounting the bearing clamp steering use sufficient water-resistant grease in the bushing. Make sure that the 2 seals are in the intended groove and are not jammed or twisted in any other place.

IMPORTANT
The reinforcement plate hast he effect through the 4 screw connection that the pressure on the screw connection oft he bracket (bearing block) is distributed over the 5-fold and much more stable surface, in ordert o protect it from consequential fall damage. Tod rill the 2 additional 5mm holes, you have to remove the front panel and the air filter box.

Jay Parts Lenksäule Performance Polaris JP0064 vs Original

If your steering stem has such entry marks as in the photo on the lef, we recommend a new steering stem, e.g. our steering stem Performance JP0064. This has been specially developed for use. You can find it in the shop or at our Flagshipstore Partners.

Torque M8 screws: 25 NM
TorqueM5 screws: 7 NM

IMPORTANT
If the surface oft he steering stem is already closed (there is metal abrasion), our system does not improve either. We recommend a new steering stem.

When greasing, make sure that you only apply the grease until the first resistance is detected in the grease gun. Grease must not ooze out! As soon as the grease swells out, the O-ring is damaged and the seal against dirt is no longer given.

RECOMMENDATION
For lubrication we recommend BEL RAY Waterproof Grease, the best grease to protect the bearing points on your entire vehicle. You can also find in our shop.

Download assembly instructionPDF

Reviews

There are no reviews yet.

Add a review

Produktanfrage / Request to product: Bearing clamp steering + reinforcement for steering stem

    Datenschutz-Info akzeptiert * Datenschutz-Info gelesen und akzeptiert / I have read and accept the Data protection.