GATES G-FORCE C12 20C4022 – CVT Drive Belt for Polaris

SALE 81,60  81,60 

GATES G-Force C12 CVT Belt 20C4022 – Polaris

Replaces OEM # 3211077

  • optimal heat resistance
  • Advanced carbon tensile cords offer increased durability
  • Aramid fibre-loaded undercord guarantees optimum belt life
  • Neoprene component guarantees top performance
  • precise fit to the Original Equipment (OE) belt
  • no need for clutching adjustments at installation
  • Made in USA

Please note the vehicle model list!

Availability : in stock

In stock

GATES G-FORCE C12 CVT Belt 20C4022 for Polaris

The innovative G-Force C12 belts with carbon tensile cord design combine minimal stretch with extraordinary strength. The belt design allows for maintaining peak power throughout the shift curve. In addition, the carbon tensile cord provides optimal power transmission, resulting in faster acceleration, improved throttle response and consistent shifting performance.

Gates G-Force C12 belt, the first CVT belt with carbon tensile cords.
G-Force C12 CVT belts for even better performance and for faster acceleration, improved throttle response and consistent shifting performance! Advanced carbon tensile cords offer increased durability. Trapezoidal top cog and rounded bottom cog design offers superior flexibility and heat dissipation. Reinforced fibre-loaded compound guarantees optimum durability

WHY G-FORCE C12?

  • Neoprene component guarantees top performance.
  • Advanced carbon tensile cords offer increased durability.
  • Minimal stretch with extraordinary strength.
  • Designed to meet or exceed OE standards.
  • First CVT Belt with carbon tensile cord design.

Made in USA

ATTENTION
Not only correct assembly but also correct retraction of the belt is extremely important for the service life of every belt!

Please note the vehicle model list!

KATALOG MOTORSCHLITTEN

Troubleshoot

GATES G-FORCE POWERSPORT BELT FAILURE ANALYSIS – IDENTIFY AND TROUBLESHOOT CVT DRIVE ISSUES

SYMTOM | POTENTIAL COUSES | RECOMMENDATIONS ⇒ READ FULL DOCUMENT FROM GATES (pdf)

Gates G-Force Powersports Belt Failure Analysis --> Identify and Troubleshoot CVT DRive Issues

Installation

CVT-BELT INSTALLATION & BREAK IT IN

Not only correct assembly but also correct retraction of the belt is extremely important for the service life of every belt!

NEW BELT INSTALLATION

Choosing the right belt for your vehicle is critical for optimum performance. Please use the JAY PARTS drive belt finder. To ensure optimal operation of newly installed belts, the CVT sheaves must be cleaned of all old belt residue, dirt, debris, and oils. If any particles remain, belt slip and a noticeable drop in vehicle performance can occur

Jay Parts Reinigung Veriomatik vor Riemenwechsel

At JAY PARTS  there is a 3D-Softflex – Non-Woven Abrasives-Pad FREE of charge with every GATES G-FORCE REDLINE CVT drive belt! Remove old belt residue, dirt, debris, and oils from the clutch sheaves with 3D-Softflex non-woven abrasives pad and isopropanol alcohol or acetone poured or sprayed on a rag.
ATTENTION: Do not spray onto the clutches and do not use brake cleaner.

  1. Make sure the vehicle is in park or neutral and the engine is off. Remove the cover of the clutch.
  2. If possible, blow out the clutches and all inlet and outlet openings in the clutch box with compressed air to remove dust, dirt and debris. If the previous belt broke, remove all the debris and cord if any are left in the primary or secondary clutches. Completely clear all inlets and outlets, especially the variomatic outlet, of any belt residue.
  3. If possible, check for correct alignment by checking the center-to-center distance between the primary and secondary clutch, see the vehicle manufacturer’s manual.
  4. Clean the clutch sheaves with the 3D-Softflex Non-Woven Abrasives-Pad and wipe them clean with isopropanol alcohol or acetone poured or sprayed on a rag – do not spray onto the clutches. Repeat this procedure until the sheaves surfaces are completely cleaned and dry. Do NOT use brake cleaner!
    This removes the old belt residue and oils which can cause the new belt to slip.
  5. Open the secondary clutch with suitable tools as recommended by the OEM. Install the new belt so the lettering can be read right side up. Although G-Force belts are not directionally biased, it is recommended to install them with the label lettering facing toward the user to keep belt reinstallation consistent. DO NOT FIT THE NEW BELT WITH A LEVER. (Note: When reinstalling the belt, always install it in the previous orientation to keep the belt wear profile aligned with the sheaves profile.)
  6. After installation, release the tension on the secondary clutch. Turn the secondary clutch anticlockwise until the belt reaches its initial position.
  7. Remove the tool that may have been placed on the vehicle.
  8. Mount the clutch cover on vehicles with a vario shaft mounted in the cover. If the vario shaft isn’t mounted in the cover, start unit up in park and let it idle for 30 seconds. Turn off the engine and replace the clutch cover. Give a quick throttle.
    CAUTION: DO NOT reach into the clutch (rotating parts)
    If the belt doesn’t come to rest and stop spinning in Park and the idle has dropped to normal warm engine rpm, check your system for alignment and proper operation of the variomatic. On snowmobiles you may need to adjust your deflection several times.
  9. See the vehicle Owner’s Manual for proper alignment and center-to-center distances of the clutch system.
  10. When the belt stops in park and neutral mode, replace the cover and proceed to break-in process of a new belt.

PERFORM A HEAT CYLE – DON’T BREAK IT. BREAK IT IN.

If you take the time to break in a new belt gently and carefully, the belt will run smoother and you will have maximum life and performance. Follow the next HEAT CYCLES:

  1. Drive the unit in two wheel high for 20 minutes between 25-45 mph (40-72 km/h) avoiding hard accelerations and hills. Flat terrain works best. Vary vehicle speed and engine rpm to cycle the belt in the normal operating range, but not more than ¾ of the maximum force during retraction. In extremely cold weather, it is advisable to extend the break-in time by 5-10 minutes to allow the belt to warm up optimally.
  2.  After 20 minutes of driving, let the unit cool down for 30 minutes with the motor off.
  3. Repeat the HEAT CYCLE for a second time. Let the belt cool down again for 30 minutes.
  4. Repeat the HEAT CYCLE for a third time. Let the belt cool down again for 30 minutes and you have a well broken in belt.
KAT/CAT Marke/Brand Jahr/Year Modell/Model
KAT/CAT Marke/Brand Jahr/Year Modell/Model
Belt Polaris 1985 - 1986 Scrambler 250
Belt Polaris 1985 - 1999 Trail Boss 250
Belt Polaris 1989 - 1993 Big Boss 250
Belt Polaris 1990 - 1993 Trail Boss 350L
Belt Polaris 1990 - 1995 Trail Blazer 250
Belt Polaris 1991 - 1992 Big Boss 6x6
Belt Polaris 1993 Big Boss 350L 6x6
Belt Polaris 1994 - 1995 400L
Belt Polaris 1994 Big Boss 300 6x6
Belt Polaris 1994 - 1997 Big Boss 400L 6x6
Belt Polaris 1994 - 1997 Sportsman 400
Belt Polaris 1994 - 2001 Sport 400
Belt Polaris 1995 - 1997 Xplorer 400L
Belt Polaris 1995 - 1998 Magnum 425
Belt Polaris 1995 - 2002 Scrambler 400
Belt Polaris 1996 - 1997 Magnum 6x6
Belt Polaris 1996 - 1997 Trail Blazer ES 250
Belt Polaris 1996 - 1997 Xpress 400L
Belt Polaris 1996 - 1999 Xplorer 300
Belt Polaris 1996 - 1999 Xpress 300
Belt Polaris 1996 - 2001 Sportsman 500
Belt Polaris 1997 Magnum 4x4
Belt Polaris 1997 - 2006 Trail Blazer 250
Belt Polaris 1997 - 2012 Scrambler 500
Belt Polaris 1997 Xplorer 500
Belt Polaris 1998 - 1999 Big Boss 500 6x6
Belt Polaris 1998 - 2001 Sportsman 350
Belt Polaris 1998 - 2002 Xplorer 400
Belt Polaris 1998 - 2009 Ranger 500
Belt Polaris 1999 Worker 335
Belt Polaris 1999 Worker 500
Belt Polaris 2000 - 2002 Magnum 325
Belt Polaris 2000 Magnum 500
Belt Polaris 2000 - 2002 Trail Boss 325
Belt Polaris 2000 - 2002 Xplorer 250
Belt Polaris 2000 - 2004 Ranger 425
Belt Polaris 2000 - 2008 Sportsman 500 6x6
Belt Polaris 2001 - 2002 Trail Boss 250
Belt Polaris 2001 Worker 500
Belt Polaris 2002 - 2005 Sportsman 425
Belt Polaris 2002 Sportsman 500 HO
Belt Polaris 2003 - 2006 Magnum 330
Belt Polaris 2003 Trail Blazer 400
Belt Polaris 2003 - 2013 Trail Boss 330
Belt Polaris 2004 - 2005 ATP 330
Belt Polaris 2006 - 2007 Sportsman 455
Belt Polaris 2006 Sportsman 500 HO
Belt Polaris 2007 - 2008 MV500
Belt Polaris 2007 Sportsman 500
Belt Polaris 2008 Sportsman 500 HO
Belt Polaris 2008 - 2013 Trail Blazer 330
Belt Polaris 2009 - 2013 Sportsman 500
Belt Polaris 2010 Ranger 425
Belt Polaris 2011 - 2014 Ranger 455
Belt Polaris 2011 - 2014 Sportsman 455
Belt Polaris 2015 Sportsman 325
Belt Polaris 2015 Sportsman Hawkeye 300
Belt Polaris 2016 Sportsman Hawkeye 325

Reviews

There are no reviews yet.

Add a review

Produktanfrage / Request to product: GATES G-FORCE C12 20C4022 - CVT Drive Belt for Polaris

    Datenschutz-Info akzeptiert * Datenschutz-Info gelesen und akzeptiert / I have read and accept the Data protection.